A Step-by-Step Guide to Setting Up a Tub
A Step-by-Step Guide to Setting Up a Tub
Blog Article
Just how do you actually feel in relation to A Step-by-Step Guide to Installing a Bathtub?
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is additionally a moderately difficult task. If the old tub is readily obtainable, the job can relocate immediately; if you have to open up a wall to eliminate the old bathtub as well as position the new bath tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as embeded in the new one. Make sure you have actually qualified on your own for the job as well as fit attempting it. Instead of hiring a specialist to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you start. Chances are you might need a specialist plumber to make tube connections.
This short article will certainly help you set up a brand-new bath tub in your restroom if you have actually currently bought a new bathtub and also don't need to transform the setup of your previous supply of water pipelines.
Your devices and also material checklist must consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the water supply. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of removing the existing taps can be quite troublesome because of the limited accessibility that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly come from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Before moving on to fit the new faucets, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the tap as well as the other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin guaranteeing that the washing machines are in place in between the faucet and the sink. Protect the tap in position with the producer given backnut. When the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap adapters. The former type must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Mounting the Tub
Making use of the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are helpful in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four little points.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the bathtub up until the level reads degree.
To install taps, fit all-time low of the furthest versatile faucet port to the proper supply pipeline by making a compression join; after that do the very same for the other faucet.
Activate the supply of water as well as examine all joints and brand-new pipework for leakages and tighten them if needed. Load the bathtub and additionally check the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, deal with the bath paneling as described in the producer's user's manual. Tiling and also sealing around the tub ought to wait till the bath tub has actually been used at least once as this will resolve it right into its last position.
Getting ready for the Setup
To start with, the sustaining structure provided with the bath ought to be fitted (if needed) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to make certain that if the faucet features a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to prevent strain on the tub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you make use of every one of the provided washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture an inflexible seal, triggering the water to permeate the wall in between the bathroom and the tiling, leading to difficulties with moisture as well as possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the bathtub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealant can fracture relatively early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently offered on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that blog entry about Installing A Bathtub while perusing the search engines. Sharing is good. Helping others is fun. Thank you for your time. Visit us again soon.
This Site
Report this page